 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| TD62064APG/AFG TOSHIBA Bipolar Digital Integrated Circuit Silicon Monolithic TD62064APG, TD62064AFG 4ch High-Current Darlington Sink Driver The TD62064APG/AFG are high-voltage, high-current darlington drivers comprised of four NPN darlington pairs. All units feature integral clamp diodes for switching inductive loads. Applications include relay, hammer, lamp and stepping motor drivers. The suffix (G) appended to the part number represents a RoHS product. TD62064APG Features * * * * * * * Output current (single output) 1.5 A (max) High sustaining voltage output 50 V (min) Output clamp diodes Input compatible with TTL and 5 V CMOS GND terminal = Heat sink Package type-AP: DIP-16 pin Package type-AF: HSOP-16 pin Weight DIP16-P-300-2.54A: 1.11 g (typ.) HSOP16-P-300-1.00: 0.50 g (typ.) TD62064AFG Pin Assignment (top view) TD62064APG O4 16 NC 15 I4 14 Heat sink & GND 13 12 I3 11 NC 10 O3 9 1 COM 2 O1 3 I1 4 5 Heat sink & GND 6 I2 7 O2 8 COM TD62064AFG O4 16 NC 15 I4 14 NC 13 Heat sink & GND NC 12 I3 11 NC 10 O3 9 1 COM 2 O1 3 I1 4 NC Heat sink & GND 5 NC 6 I2 7 O2 8 COM 1 2007-10-16 TD62064APG/AFG Schematics (each driver) COMMON Input 8.2 k 230 1.1 k Output GND Note: The input and output parasitic diodes cannot be used as clamp diodes. Precautions for Using (1) This IC does not include built-in protection circuits for excess current or overvoltage. If this IC is subjected to excess current or overvoltage, it may be destroyed. Hence, the utmost care must be taken when systems which incorporate this IC are designed. Utmost care is necessary in the design of the output line, COMMON and GND line since IC may be destroyed due to short-circuit between outputs, air contamination fault, or fault by improper grounding. This IC is being used to drive an inductive load (such as a motor, solenoid or relay), Toshiba recommends that the diodes (pins 1 and 8) be connected to the secondary power supply pin so as to absorb the counter electromotive force generated by the load. Please adhere to the device's absolute maximum ratings. Toshiba recommends that zener diodes be connected between the diodes (pins 1 and 8) and the secondary power supply pin (as the anode) so as to enable rapid absorption of the counter electromotive force. Again, please adhere to the device's absolute maximum ratings. (2) Absolute Maximum Ratings (Ta = 25C) Characteristics Output sustaining voltage Output current Input current Input voltage Clamp diode reverse voltage Clamp diode forward current Power dissipation Operating temperature Storage temperature APG AFG Symbol VCE (SUS) IOUT IIN VIN VR IF PD Topr Tstg Rating -0.5 to 50 1.5 50 -0.5 to 17 50 1.5 1.47/2.7 (Note 1) 0.9/1.4 (Note 2) -40 to 85 -55 to 150 Unit V A/ch mA V V A W C C Note 1: On glass epoxy PCB (50 x 50 x 1.6 mm Cu 50%) Note 2: On glass epoxy PCB (60 x 30 x 1.6 mm Cu 30%) 2 2007-10-16 TD62064APG/AFG Operating Conditions (Ta = -40 to 85C) Characteristics Output sustaining voltage Symbol VCE (SUS) Test Condition DC1 circuit, Ta = 25C APG (Note 1) Tpw = 25 ms 4 circuits Tj = 120C Ta = 85C VIN Input voltage Output ON Output OFF Input current Clamp diode reverse voltage Clamp diode forward current Power dissipation APG AFG VIN (ON) VIN (OFF) IIN VR IF PD Ta = 85C Ta = 85C IOUT = 1.25 A (Note 1) (Note 2) Duty = 10% Duty = 50% Duty = 10% Duty = 50% Min 0 0 0 0 0 0 0 2.5 0 0 0 Typ. Max 50 1250 1250 390 907 172 8 8 0.4 20 50 1.25 1.4 0.7 mA V A W V mA/ch Unit V Output current IOUT AFG (Note 2) Note 1: On glass epoxy PCB (50 x 50 x 1.6 mm Cu 50%) Note 2: On glass epoxy PCB (60 x 30 x 1.6 mm Cu 30%) Electrical Characteristics (Ta = 25C) Characteristics Output leakage current Symbol ICEX Test Circuit 1 Test Condition VCE = 50 V, Ta = 25C VCE = 50 V, Ta = 85C IOUT = 1.25 A, IIN = 2 mA IOUT = 0.75 A, IIN = 935 A VCE = 2 V IOUT = 1.0 A IOUT = 0.25 A Min Typ. 800 1500 15 0.1 1.0 Max 50 500 1.6 1.25 2.4 50 100 2.0 Unit A Output saturation voltage VCE (sat) 2 V DC current transfer ratio Input voltage (output on) Clamp diode leakage current Clamp diode forward voltage Input capacitance Turn-ON delay Turn-OFF delay hFE VIN (ON) IR VF CIN tON tOFF 2 3 4 5 6 7 7 V A V pF s s IOUT = 1.25 A, IIN = 2 mA VR = 50 V, Ta = 25C VR = 50 V, Ta = 85C IF = 1.25 A VIN = 0 V, f = 1 MHz CL = 15 pF, VOUT = 50 V, RL = 42 CL = 15 pF, VOUT = 50 V, RL = 42 3 2007-10-16 TD62064APG/AFG Test Circuit 1. ICEX Open ICEX Open VCE VCE, VCE (sat) VIN (ON) VCE IIN 2. VCE (sat), hFE Open IOUT 3. VIN (ON) Open IOUT 4. IR 5. VF VF VR Open Open 6. CIN Open fi Capacitance bridge LO Open VIN IR Open Open IF 7. tON, tOFF Input Open VOUT RL Pulse generator (Note 1) VIN Output CL = 15 pF (Note 2) Output Input tr 90% 50% 10% tON 50% 50 s (Note 1) tf 90% 50% 10% tOFF 50% VOL VIH = 2.4 V 0 VOH Note 1: Pulse Width 50 s, Duty Cycle 10% Output Impedance 50 , tr 5 ns, tf 10 ns Note 2: CL includes probe and jig capacitance 4 2007-10-16 TD62064APG/AFG IOUT - VCE (sat) 1.5 TD62064APG 12 TD62064APG IIN - VIN (A) IOUT 1.0 typ. 25C max Input current IIN (mA) max 8 typ. min Output current 0.5 4 0 0 0.5 1.0 1.5 2.0 0 1.0 2.0 3.0 4.0 5.0 Collector-emitter saturation voltage VCE (sat) (V) Input voltage VIN (V) IOUT - IIN 3.0 400 VCE = 2 V (1) 2.4 PD - Ta (1) DIP-16 pin on glass epoxy PCB (50 x 50 x 1.6 mm Cu 50%) (2) DIP-16 pin free air (3) PFP-16 pin on glass epoxy PCB (60 x 30 x 1.6 mm Cu 30%) (2) 1.2 (3) (4) PFP-16 pin free air (mA) Ta = 75 C 25 -30 Power dissipation PD IOUT 300 (W) 200 1.8 Output current 100 (4) 0.6 0 50 100 150 200 0 0 40 80 120 160 200 Input current IIN (A) Ambient temperature Ta (C) IOUT - Duty cycle 1500 n=1 1500 IOUT - Duty cycle n=1 (mA) n=3 900 n=4 n=2 (mA) 1200 1200 n=4 900 n=3 n=2 IOUT Output current Output current IOUT 600 600 300 TD62064APG Ta = 25C n-ch ON 300 TD62064APG Ta = 85C n-ch ON 0 0 20 40 60 80 100 0 0 20 40 60 80 100 Duty Cycle (%) Duty Cycle (%) 5 2007-10-16 TD62064APG/AFG IOUT - Duty cycle 1500 n=1 1500 IOUT - Duty cycle (mA) (mA) 1200 n=4 900 n=3 n=2 1200 n=1 n=3 900 n=4 600 n=2 IOUT Output current 600 300 TD62064AFG Ta = 25C n-ch ON Output current IOUT 300 TD62064AFG Ta = 85C n-ch ON 0 0 20 40 60 80 100 0 0 20 40 60 80 100 Duty Cycle (%) Duty Cycle (%) 6 2007-10-16 TD62064APG/AFG Package Dimensions Weight: 1.11 g (typ.) 7 2007-10-16 TD62064APG/AFG Package Dimensions Weight: 0.50 g (typ.) 8 2007-10-16 TD62064APG/AFG Notes on Contents 1. Equivalent Circuits The equivalent circuit diagrams may be simplified or some parts of them may be omitted for explanatory purposes. 2. Test Circuits Components in the test circuits are used only to obtain and confirm the device characteristics. These components and circuits are not guaranteed to prevent malfunction or failure from occurring in the application equipment. IC Usage Considerations Notes on Handling of ICs (1) The absolute maximum ratings of a semiconductor device are a set of ratings that must not be exceeded, even for a moment. Do not exceed any of these ratings. Exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. Use an appropriate power supply fuse to ensure that a large current does not continuously flow in case of over current and/or IC failure. The IC will fully break down when used under conditions that exceed its absolute maximum ratings, when the wiring is routed improperly or when an abnormal pulse noise occurs from the wiring or load, causing a large current to continuously flow and the breakdown can lead smoke or ignition. To minimize the effects of the flow of a large current in case of breakdown, appropriate settings, such as fuse capacity, fusing time and insertion circuit location, are required. If your design includes an inductive load such as a motor coil, incorporate a protection circuit into the design to prevent device malfunction or breakdown caused by the current resulting from the inrush current at power ON or the negative current resulting from the back electromotive force at power OFF. IC breakdown may cause injury, smoke or ignition. Use a stable power supply with ICs with built-in protection functions. If the power supply is unstable, the protection function may not operate, causing IC breakdown. IC breakdown may cause injury, smoke or ignition. Do not insert devices in the wrong orientation or incorrectly. Make sure that the positive and negative terminals of power supplies are connected properly. Otherwise, the current or power consumption may exceed the absolute maximum rating, and exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. In addition, do not use any device that is applied the current with inserting in the wrong orientation or incorrectly even just one time. Carefully select external components (such as inputs and negative feedback capacitors) and load components (such as speakers), for example, power amp and regulator. If there is a large amount of leakage current such as input or negative feedback condenser, the IC output DC voltage will increase. If this output voltage is connected to a speaker with low input withstand voltage, overcurrent or IC failure can cause smoke or ignition. (The over current can cause smoke or ignition from the IC itself.) In particular, please pay attention when using a Bridge Tied Load (BTL) connection type IC that inputs output DC voltage to a speaker directly. (2) (3) (4) (5) 9 2007-10-16 TD62064APG/AFG Points to Remember on Handling of ICs (1) Heat Radiation Design In using an IC with large current flow such as power amp, regulator or driver, please design the device so that heat is appropriately radiated, not to exceed the specified junction temperature (Tj) at any time and condition. These ICs generate heat even during normal use. An inadequate IC heat radiation design can lead to decrease in IC life, deterioration of IC characteristics or IC breakdown. In addition, please design the device taking into considerate the effect of IC heat radiation with peripheral components. Back-EMF When a motor rotates in the reverse direction, stops or slows down abruptly, a current flow back to the motor's power supply due to the effect of back-EMF. If the current sink capability of the power supply is small, the device's motor power supply and output pins might be exposed to conditions beyond maximum ratings. To avoid this problem, take the effect of back-EMF into consideration in system design. (2) 10 2007-10-16 TD62064APG/AFG About solderability, following conditions were confirmed * Solderability (1) Use of Sn-37Pb solder Bath * solder bath temperature = 230C * dipping time = 5 seconds * the number of times = once * use of R-type flux (2) Use of Sn-3.0Ag-0.5Cu solder Bath * solder bath temperature = 245C * dipping time = 5 seconds * the number of times = once * use of R-type flux RESTRICTIONS ON PRODUCT USE * The information contained herein is subject to change without notice. 021023_D 070122EBA_R6 * TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc. 021023_A * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer's own risk. 021023_B * The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. 060106_Q * The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. 070122_C * Please use this product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 060819_AF * The products described in this document are subject to foreign exchange and foreign trade control laws. 060925_E 11 2007-10-16 |
Price & Availability of TD62064AFG
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |